The d&b audiotechnik CCL8 is a mobile specific compact cardioid line array loudspeaker for small to medium-scale sound reinforcement.

d&b CCL8 Loudspeaker NLT4 F/M

The CCL8 is part of the brand-new CL Series. As you can guess from the name, the CCL8 offers a horizontal dispersion of 80 degrees. Each cabinet weighs 17.6kg and can produce a max SPL of 137 dB.

Output directivity is maintained across the entire operating bandwidth owing to the arrangement of the forward and sideward LF drivers in combination with their processing functions. This Line Array cabinet is a 2-way passive design housing 2 x 7″ neodymium forward LF drivers, 2 x 5″ neodymium side firing LF drivers and two 1.75″ exit HF compression drivers mounted to a dedicated wave shaping device. The cylindrical wave segments of each cabinet couple without gaps and sum up coherently. Users can set Splay angles between adjacent cabinets in the range from 0° to 14° in 1° increments. The frequency response extends from 62 Hz to above 18 kHz.

Amplifiers & comparisons for the CCL8

Any current d&b amplifier can drive the CCL8. This includes the D25, D40, D80 and D90, plus all the installation range versions too. You can drive up to two CCL8 loudspeakers per amplifier channel in Line or Arc modes, or one per channel if using Array Processing.

The CCL8 is the narrower of the line array cabinets in the CL-Series range. The cabinet dimensions are 209 x 593 x 355 mm with a weight of 17.7kg. This makes the CCL a little larger than the T10 but with output characteristics more similar to the Y-Series. The directivity (and clarity) is impressive – very much worth a listen if you have the opportunity.

IPS also stock the wider dispersion CCL12 loudspeaker cabinets, alongside the CCL SUB which are all ready to hire now. You can find out more about the full CL-Series on the d&b website here.

IPS hire stock d&b CCL8 Loudspeaker cabinets are fitted with NLT4 connectors. This means they have an in and an out. They are supplied ready to go in four-way tour carts. IPS also stock a range of rigging accessories including fly-frame and ground stack adaptor options.

The d&b audiotechnik CCL12 is a mobile specific compact cardioid line array loudspeaker for small to medium-scale sound reinforcement.

d&b CCL12 Loudspeaker NLT4 F/M

The CCL12 is part of the brand-new CL Series. Following the usual d&b naming conventions, the CCL12 offers a horizontal dispersion of 120 degrees. Each cabinet weighs 17.6kg and can produce a max SPL of 136 dB.

Output directivity is maintained across the entire operating bandwidth owing to the arrangement of the forward and sideward LF drivers in combination with their processing functions. This Line Array cabinet is a 2-way passive design housing 2 x 7″ neodymium forward LF drivers, 2 x 5″ neodymium side firing LF drivers and two 1.75″ exit HF compression drivers mounted to a dedicated wave shaping device. The cylindrical wave segments of each cabinet couple without gaps and sum up coherently. Users can set Splay angles between adjacent cabinets in the range from 0° to 14° in 1° increments. The frequency response extends from 62 Hz to above 18 kHz.

Amplifiers & comparisons for the CCL12

Any current d&b amplifier can drive the CCL12. This includes the D25, D40, D80 and D90, plus all the installation range versions too. You can drive up to two CCL12 loudspeakers per amplifier channel in Line or Arc modes, or one per channel if using Array Processing.

The CCL12 is the wider dispersion of the line array cabinets in the CL-Series range. The physical cabinet dimensions are 209 x 593 x 355 mm with a weight of 17.7kg. This makes the CCL a little larger than the T10 but with output characteristics more similar to the Y-Series. The directivity (and clarity) is impressive – very much worth a listen if you have the opportunity.

IPS also stock the narrower dispersion CCL8 loudspeaker cabinets, alongside the CCL SUB which are all ready to hire now. You can find out more about the full CL-Series on the d&b website here.

IPS hire stock d&b CCL12 Loudspeaker cabinets are fitted with NLT4 connectors. This means they have an in and an out. They are supplied ready to go in four way tour carts. IPS also stock a range of rigging accessories including fly-frame and ground stack adaptor options.

The d&b audiotechnik CCL-SUB is a mobile specific small to medium format flyable cardioid subwoofer

d&b CCL-SUB Subwoofer NLT4 F/M

Designed to complement the CCL system, the CCL-SUB delivers powerful low-end extension in a compact, flyable format. The cabinet houses two long excursion neodymium drivers in an integrated cardioid setup. These are a15″ driver in a bass-reflex design facing to the front and a 10″ driver in a 2-chamber bandpass design radiating to the rear. The arrangement and tuning provide a cardioid dispersion pattern using a single amplifier channel. Its frequency response extends from 39 Hz to 150 Hz. The max SPL is 132 dB.

The cabinet dimensions are 457 x 590 x 710 mm with a weight of 44.5kg. An M20 threaded flange in the top panel accepts a corresponding pole for the deployment of TOP cabinets. Physically it is very similar to our existing B4 subs.

Amplifiers for the CCL-SUB

Any current d&b amplifier can drive the CCL-SUB. This includes the D25, D40, D80 and D90, plus all the installation range versions too. You can drive up to two subs per amplifier channel.

You can also hire the CCL8 and CCL12 loudspeaker cabinets designed to work with the CCL SUB from IPS now. For all specifications, you can find out more about the full CL-Series on the d&b website here.

IPS hire stock d&b CCL-SUB cabinets are fitted with NLT4 connectors. This means they have an in and an out.

d&b B10-SUB Subwoofer NLT4F/M

The d&b B10-SUB is a compact subwoofer ready to discretely reinforce your low frequency output. An ideal partner for our U3, U5 and U7 cabinets, especially well suited if a minimal footprint installation is important.

d&b say:

“The B10-SUB is a mobile-specific compact multipurpose subwoofer that optimally pairs with the U-Series and other compact d&b loudspeaker systems. It includes two 10” drivers, housed within a bass-reflex cabinet, that features a newly sophisticated port design. The form factor makes this subwoofer an ideal solution for small footprint applications or set-ups where low heights are necessary.” You can find the full specifications here on the d&b website.

The compact enclosure is just 280 x 706 x 565 mm. It can be used in either portrait or landscape orientation and has handy carry handles on either side. Convieniently it is also fitted with two threaded M20 speaker pole mounts which can be used in either orientation. The B10-SUB weights 27kg, and has a smart black finish matching the other system cabinets. The frequency response extends from 38 Hz to 130/100 Hz.

You can drive up to two cabinets per channel from all the current range of d&b amplifiers. We’d suggest the versatile D25 as an ideal choice – or consider the D80 if you want the full 130dB max SPL.

d&b B12-SUB

Complementing the CCL system, the ground subwoofer B12-SUB delivers powerful low-end extension in a compact format.

Technical Details from D&B:
The B12-SUB is a compact high performance cardioid subwoofer, intended for ground stacked applications only.

It houses two long excursion neodymium drivers in an integrated cardioid setup: a 15″ driver in a bass-reflex design facing to the front and a 10″ driver in a 2-chamber bandpass design radiating to the rear. The arrangement and tuning provide a cardioid dispersion pattern using a single amplifier channel. Its frequency response extends from 39 Hz to 150 Hz.

The B12-SUB has no rigging components. The manufacturer constructs the cabinet enclosure from plywood and coats it with an impact and weather-protected 2K finish. A rigid metal grill, backed by an acoustically transparent and water-repellent fabric, protects the front and rear of the cabinet. Each side panel incorporates a handle and mounted on the rear panel are four heavy duty wheels.

Two runners extend from the rear to the front panel of the cabinet protecting the bottom panel against scratching. Two correspondingly shaped recesses are incorporated in the top panel to accept these runners and prevent cabinet movement when stacking. Find the full technical specifications here on the D&B website.

Looking for a flown version? Check out the CCL-SUB here.

The V-SUB is an actively driven high performance cardioid subwoofer powered by a single amplifier channel. The V-SUB features integrated rigging equipment, and shares the same acoustical and visual design as the V-GSUB, which is intended for ground stacked applications only. It houses two long excursion neodymium drivers, an 18″” driver in a bass-reflex design facing to the front and a 12″” driver in a two chamber bandpass design radiating to the rear. The cardioid dispersion pattern resulting from this approach avoids unwanted energy behind the system that reduces the reverberant field at low frequencies and provides the greatest accuracy of low frequency reproduction.

The V subwoofer can be used to supplement V8 and V12 loudspeakers in various combinations, ground stacked or flown, either integrated on top of a V8 / V12 array or as a separate column.

The V-SUB cabinet is constructed from marine plywood and has an impact and weather protected PCP (Polyurea Cabinet Protection) finish. The front of the loudspeaker cabinet is protected by a rigid metal grill backed by an acoustically transparent foam. Each side panel incorporates two handles, whilst the top panel has an M20 high stand flange inserted.

The Y-SUB is an actively driven cardioid subwoofer powered by a single amplifier channel. It houses two long excursion neodymium drivers in an integrated cardioid setup, an 18 1D driver in a bass-reflex chamber facing to the front and a 12 1D driver in a two chamber bandpass design radiating towards the rear. The cardioid dispersion pattern resulting from this arrangement avoids the distribution of energy behind the system, providing the greatest accuracy of low frequency reproduction and reducing the energy dispersed into unwanted areas. The Y-SUB is fitted with three point rigging hardware and can be flown in a column of purely Y subwoofers, at the top of a Y array or used in a ground stacked setup. The cabinet is constructed from marine plywood and has an impact and weather protected PCP (Polyurea Cabinet Protection) finish. The front of the loudspeaker cabinet is protected by a rigid metal grill backed by an acoustically transparent foam, whilst the side panels incorporate two handles with four wheels mounted to the rear. An optional transport lid protects the front of the subwoofer during transit.

The B4-SUB is an actively driven cardioid subwoofer powered by a single amplifier channel. It houses two long excursion neodymium drivers in an integrated cardioid setup: a 15″ driver in a bass-reflex design facing to the front and a 12″ driver in a two chamber bandpass design radiating to the rear. The cardioid dispersion pattern resulting from this approach avoids unwanted energy behind the system that greatly reduces the reverberant field at low frequencies and provides the greatest accuracy of low frequency reproduction. The B4 subwoofer can only be used in a ground stacked setup. The B4-SUB cabinet is constructed from marine plywood, has an impact and weather resistant paint finish and a pair of handles. An M20 threaded flange in the top panel accepts the d and b Loudspeaker stand winder M20. The loudspeaker cabinet is also available in Special Colour (SC) options.

The V12 is a 3-way passive design housing 2 x 10inch LF drivers, one hornloaded 8inch MF driver and two 1.4inch exit HF compression drivers with 2.5inch voicecoils mounted to a dedicated waveshaping device. The symmetrical dipolar arrangement of the neodymium LF drivers around the centrally mounted coaxial MF and HF components allows a smooth overlap of the adjacent frequency bands in the crossover design. This results in an exceptional 120deg horizontal constant directivity dispersion control nominally being maintained down to 250 Hz. The mechanical and acoustical design enables flown vertical arrays of up to twenty four loudspeakers. It can be used in columns of purely V12 loudspeakers or combined with V8s and / or with V-SUBs. The cabinet is constructed from marine plywood and has an impact and weather protected PCP (Polyurea Cabinet Protection) finish. The front of the loudspeaker cabinet is protected by a rigid metal grill backed by an acoustically transparent foam. Each side panel incorporates a handle, while two additional recessed grips are provided at the rear bottom of the cabinet.

The d&b V7P Loudspeaker is the largest point‑source option in the IPS d&b hire range.

The 3‑way passive V7P uses two 10‑inch drivers in a dipole arrangement. These drivers work together with a horn‑loaded 8‑inch MF driver and a 1.4‑inch compression driver mounted on a rotatable CD horn. Furthermore, the innovative horn design for the centrally mounted MF driver delivers remarkable sensitivity, which results in exceptional vocal performance. In addition, an advanced bass‑reflex and venting design extends the LF output and provides full‑bandwidth capability. All components sit symmetrically around the cabinet’s centre axis, thereby producing a perfectly symmetrical dispersion pattern. This high‑performance point‑source loudspeaker offers 75° horizontal directivity with a 40° vertical dispersion. Moreover, you can rotate the horn by 90° to enable horizontal orientation. You can find the full specification for the V7P on the d&b audiotechnik website.

The V7P supports a wide range of deployment options. You can use it as a stand‑alone full‑range system or combine it with other V‑Series elements, either ground‑stacked or flown. The d&b V‑SUB is a popular subwoofer partner.

The cabinet is built from marine plywood. It has a black impact and weather resistant PCP (Polyurea Cabinet Protection) finish. A rigid metal grille protects the front of the loudspeaker. The enclosure includes a pair of handles, M10 threaded inserts for d&b rigging hardware, and three additional M10 sockets that accept an 8 mm load pin to expand mounting options.

IPS hire stock V7P loudspeakers are fitted with NL4 connectors. You can drive the V7P with d&b D20, D25, D40, D80, or D90 amplifiers, with up to two V7P cabinets per channel.

The Z5385 V Flying adapter must only be used in conjunction with
the d and b V-Series V8 and V12 loudspeakers

The Stack adapter is attached to the rear rigging strand of the V-SUB cabinet.

d&b V Series Line Array Flying Frame Z5380

The d&b Y10P Loudspeaker is one of the most popular point source hire choices at IPS.

The compact 2‑way passive Y10P loudspeaker uses two 8‑inch drivers in a dipole arrangement. A 1.4‑inch compression driver mounted on a rotatable CD horn provides HF coverage. Sophisticated horn geometry, combined with the advanced bass‑reflex port design, delivers full‑bandwidth performance with extended LF output.

These high‑performance point‑source cabinets offer 110° horizontal directivity controlled down to 500 Hz, matched with a 40° vertical dispersion. You can rotate the horn by 90° to enable horizontal orientation. As a result, the Y10P supports a wide range of deployment options. You can use it as a stand‑alone full‑range system or combine it with other Y‑Series elements, either ground‑stacked or flown. IPS also stock the narrower dispersion Y7P speaker option too.

The cabinet is constructed from marine plywood and finished with impact‑ and weather‑resistant PCP (Polyurea Cabinet Protection). A rigid metal grille backed with acoustically transparent foam protects the front of the loudspeaker. The enclosure incorporates a pair of handles, while M10 threaded inserts support d&b rigging hardware. Additionally, two further M10 sockets accept an 8 mm load pin to expand mounting options. Full Y10P specifications are available on the d&b audiotechnik website.

IPS hire stock d&b Y10P Loudspeaker include NL4 connectors and come supplied in wheeled two way flightcases. You can drive the Y10P with a range of d&b amplifiers, including the D20, D25, D40, and D80. A maximum of two Y10P cabinets can be driven per amplifier channel. IPS has a range of d&b loudspeakers, amplifiers and processing equipment ready to hire, including an extensive range of other audio hardware.

The V8 is a 3-way passive design housing 2 x 10inch LF drivers, one hornloaded 8inch MF driver and two 1.4inch exit HF compression drivers with 2.5inch voicecoils mounted to a dedicated waveshaping device. The symmetrical dipolar arrangement of the neodymium LF drivers around the centrally mounted coaxial MF and HF components allows a smooth overlap of the adjacent frequency bands in the crossover design. This results in an exceptional 80deg horizontal constant directivity dispersion control nominally being maintained down to 250 Hz. The mechanical and acoustical design enables flown vertical arrays of up to twenty four loudspeakers. It can be used in columns of purely V8 loudspeakers or combined with V12s and / or with V-SUBs. The V8 cabinet is constructed from marine plywood and has an impact and weather protected PCP (Polyurea Cabinet Protection) finish. The front of the loudspeaker cabinet is protected by a rigid metal grill backed by an acoustically transparent foam. Each side panel incorporates a handle, while two additional recessed grips are provided at the rear bottom of the cabinet.

d&b Y8 Line Array Element

d&b Y8 line array ready to hire from IPS. Uaually supplied in four way tour carts/dollys, these 80 degree dispersion boxes are the middle size offering from IPS. We also stock the smaller T10 series, and the larger V series too. The Y8 can be hire as individual cabinets, or as a full system including amplifiers, cabling and much more.

Y8 Technical Specification:

The compact Y8 loudspeaker is designed for use in vertical columns to form the d&b Y8 Line Array System. The 2-way passive design features two 8inch drivers in a dipole arrangement and a centrally mounted 1.4inch compression driver with a wave transformer. Sophisticated horn geometry combined with the advanced bass-reflex port design delivers full bandwidth capabilities with an extended LF output. These high performance line array modules offer 80deg horizontal directivity controlled down to 500 Hz. The mechanical and acoustical design enables vertical arrays of up to twenty four loudspeakers with vertical splay angles from 0deg to 14deg with a 1deg resolution. Users can deploy the system in columns of purely Y8 loudspeakers or combine it with Y12 (not an IPS stock item) and/or Y-SUB cabinets.

Audio experts d&b construct the loudspeaker cabinet from marine plywood and apply an impact- and weather-protected PCP (Polyurea Cabinet Protection) finish. A rigid metal grill backed by acoustically transparent foam protects the front of the loudspeaker cabinet. Each side panel incorporates three point rigging hardware integrated into the loudspeaker enclosure. This is plus a handle, while two additional recessed grips are provided at the rear.  Check out full product details here on the d&b website.

Amplifier Options & Cabling

IPS hire stock Y8 cabinets are fitted with speakON NL4 connectors.

d&b Y8 Line Rigging

IPS have a range of rigging options for hire for the Y8. Options inclue the d&b Y8 z5390 Flying Frame and the d&b Z5396Y Base plate/stack adapter.

The d&b Y7P Loudspeaker is one of the most popular point source hire choices at IPS.

The compact 2‑way passive Y7P loudspeaker uses two 8‑inch drivers in a dipole arrangement. A 1.4‑inch compression driver mounted on a rotatable CD horn provides HF coverage. Sophisticated horn geometry, combined with the advanced bass‑reflex port design, delivers full‑bandwidth performance with extended LF output.

These high‑performance point‑source cabinets offer 75° horizontal directivity controlled down to 500 Hz, matched with a 40° vertical dispersion. You can rotate the horn by 90° to enable horizontal orientation. As a result, the Y10P supports a wide range of deployment options. You can use it as a stand‑alone full‑range system or combine it with other Y‑Series elements, either ground‑stacked or flown. IPS also stock the wider 110degree dispersion Y10P speaker option – and also the big brother V7P version too.

The cabinet is constructed from marine plywood and finished with impact‑ and weather‑resistant PCP (Polyurea Cabinet Protection). A rigid metal grille backed with acoustically transparent foam protects the front of the loudspeaker. The enclosure incorporates a pair of handles, while M10 threaded inserts support d&b rigging hardware. Additionally, two further M10 sockets accept an 8 mm load pin to expand mounting options. Full Y7P specifications are available on the d&b audiotechnik website.

IPS hire stock d&b Y7P Loudspeaker include NL4 connectors and come supplied in wheeled two way flightcases. You can drive the Y7P with a range of d&b amplifiers, including the D20, D25, D40, and D80. A maximum of two Y7P cabinets can be driven per amplifier channel. IPS has a range of d&b loudspeakers, amplifiers and processing equipment ready to hire, including an extensive range of other audio hardware.

d&b Y Series Line Array Flying Frame Z5390 Hire

Designed to fly vertical arrays of d&b Y8 Line Array cabinets – and also can be used to fly the d&b Y-SUB too. The d&b Y8 Flying Frame Z5390 is a tour ready Line Array fly solution ready to hire. Designed for single or two point rigging, the frame can also be used with the Rotaclamp. Perfect for quick onsite deployment, users can fit the fly frame whilst the cabinets are still in the tour cart, making this a great tour solution.

Users must use Y-Series rigging components (Flying frame, Load adapter, Locking pins) only with d&b Y-Series loudspeakers.

Users can use the Z5390 Y Flying frame to suspend a total system weight of 540 kg SWL. This can consist of up to 24 Y-TOP cabinets or a SUB column with a maximum of 10 Y-SUB cabinets.

Rigging components enable users to fly arrays of up to 10 Y-TOP cabinets, with a total system weight of 220 kg, in any vertical splay angle configuration between the cabinets. For any other array configuration, users must check the load conditions within the array using the d&b ArrayCalc simulation software.

IPS d&b Y8 Flying Frame Z5390 Kit contents

Supplied from IPS in a two way flight case, each frame comes with the following components:

4x 1.5t Shackle

2x Y Load Adaptor with 2x 10mm Locking Pin

Y Load Adaptor Rota Clamp with 2x 10mm Locking Pin

2x Front Link

2x 07mm Locking Pins

Splay Link

Cable Pick O Ring

2x 08mm Locking Pins

Hoist Connector Chain Z5391

Safety Chain Set Z5392

Cable Choke – Line Array (for cable management)

2x PA Rope (for brailing/steering array)

d&b Rota Clamp Z5147

Safety Bond 150KG WLL

The T10 is a passive 2-way loudspeaker housing two 6.5″ drivers positioned in a dipolar arrangement and a 1.4″ HF compression driver and a passive crossover network. The T10 can be used both as a line array and as a high directivity point source loudspeaker. The HF driver is fitted to a unique waveguide horn producing vertical line source directivity with a 90deg horizontal pattern that is maintained down to approximately 600 Hz. An acoustic lens placed in front of the horn widens horizontal dispersion to 105deg, rotation of the horn by 90deg relative to this produces an accurate point source dispersion, transforming a vertically oriented T10 into a stand-alone full range loudspeaker with 90deg horizontal and 35deg vertical directivity pattern. The T10 cabinet is constructed from polyurethane integral hard foam, incorporates integrated line array rigging hardware and has an impact resistant finish. The front of the loudspeaker cabinet is protected by a rigid metal grill backed by an acoustically transparent foam, and two NL4 connectors wired in parallel are mounted on the rear panel.

The Z5373T Cluster bracket allows up to three T10 loudspeaker
cabinets to be mounted and set to different horizontal or vertical angles.
For this purpose two M8 threaded inserts at the d and b standard spacing
of 115 mm (4.5inch) together with a center M10 thread are integrated in
the tie bar of the bracket.

The maximum permitted working load of the bracket is 33 kg (73 lb)
(according to BGV C1) which corresponds to the weight of a maximum
of three T10 loudspeakers.

d&b T Series Line Array Flying Frame Z5370

The Z5372 T Horizontal bracket must only be used in conjunction with
d and b T10 loudspeakers

The d&b E12X-SUB is a compact, lightweight, high performance subwoofer for use with d&b E-Series loudspeakers.

The built‑in passive crossover network lets the E12X‑SUB operate in parallel with the E8 loudspeaker on the same amplifier channel, greatly extending the systems’ low‑frequency headroom and bandwidth. You can also run it in active mode on its own amplifier channel without making any changes to the subwoofer. In Active mode, the E12X‑SUB supplements any E‑Series cabinet — including the compact E6.

Ideal for smaller applications where you need the low frequency response of a subwoofer without the space needed for a larger unit. Constructed from marine plywood with an impact resistant finish, the cabinet is easy to move about and deploy thanks to a handle and an M20 threaded flange on the top. This accepts the d&b Loudspeaker stand winder M20. The IPS hire models are fitted with NL4 input and output connectors. You can find the full specifications here on the d&b website.

You can drive up to two E12X-SUB cahinets per amplifier channel. Suitable amplifiers include the d&b D20, D40, D80, D90 and D25.

The d&b audiotechnik E12X-SUB is ready to hire now from IPS. It is also available to buy as an ex rental item – check out the full list here.

The Z5351 E8 Horizontal bracket enables E8 loudspeaker cabinets to
be mounted and set to different horizontal or vertical angles.

The E8 is a high performance 2-way multipurpose loudspeaker, employing an integrated coaxial driver. The E8 can be used for speech and music applications as a stand-alone full range system, or incorporated into larger distributed sound reinforcement situations. With the addition of an E12X subwoofer in passive or active mode or any other E-Series subwoofer, it can also easily reproduce higher level music program. The multifaceted shape of the enclosure allows use either in an upright or horizontal orientation as well as deployment as a stage monitor. The 90deg x 50deg dispersion pattern (h x v) of the horn is easily rotatable through 90deg to provide a 50deg x 90deg dispersion pattern. The E8 cabinet is constructed from polyurethane integral hard foam with an impact resistant paint finish incorporating a handle and a socket to accept loudspeaker stands. The loudspeaker cabinet is also available in Special Color (SC) and Weather Resistant (WR) options. The Weather Resistant option provides an IP54 rating, and enables operation of loudspeakers in changing ambient conditions. Both options are supplied with metal plates in the specified colour covering the handle recesses and loudspeaker stand socket.

d&b E6 Horizontal Bracket Z5378

Designed specifically to be used with the compact d&b E6 loudspeaker. This bracket enables the E6 to be supported in a horizontal configuration to get audio exactly where it is needed. This orientation enables maximum benefit from the small horizontal dimension of the E6 cabinet. These brackets enable the E6 to be ‘tucked’ into a wide range of postions. Perfect for when ubobtrusive audio reinforcement is required. Applications include under or over LED display screens and many more. The bracket can also be used in a vertical configuration if required, whilst still providing coverage adjustment in the horizontal plane.

The bracket includes a central 12.5mm hole and a further two 9mm holes either side for attaching mounting hardware. You can find full mounting instructions to download here on the d&b audiotechnik website.

The d&b E6 Horizontal Bracket Z5378 is a genuine d&b accessory. It is metal in construction, and is provided in a smart black painted finish to match the other E6 speaker cabinet hardware.

IPS have a range of different speaker options ready to hire from d&b, including an extensive range of rigging hardware. If this bracket does not provide the rigging option you require, please talk to our hire team for other suggestions.

Perfect for discreet audio reinforcement, the d&b E6 Loudspeaker is a relatively small high performance multipurpose cabinet.

The E6 employs an integrated coaxial driver. The horn with its 100deg x 55deg dispersion pattern can easily be rotated through 90deg providing a 55deg x 100deg pattern without the use of tools. This enables deployment of the loudspeaker either vertically or horizontally. Its distinctive cabinet design and extensive range of accessories allow easy deployment in almost any situation, including stage monitoring.

It provides a very compact reinforcement solution that inspires through its sound quality and is also perfectly compatible with the larger E8 and E12 loudspeakers. With the addition of an E12X subwoofer it can also reproduce high level music program if required.

The E6 cabinet has an impact resistant black paint finish incorporating a handle. Especially when used with a cast base speaker stand, the E6 is one of the most popular compact conference and event production loudspeaker around. Full E6 specifications are available on the d&b audiotechnik website.

IPS hire stock d&b E6 Loudspeaker include NL4 connectors and come supplied in four and six way flightcases. You can drive the E6 with a range of d&b amplifiers, including the D20, D25, D40, and D80. IPS has a range of d&b loudspeakers, amplifiers and processing equipment ready to hire, including an extensive range of other audio hardware.

The Z5396 must only be used for ground stacked applications in
connection with d and b Y-Series Y8 and Y12 cabinets
The Base plate is not intended for flown use.
Note: Please note that the Base plate is not compatible/
applicable in connection with d and b Yi8 and Yi12 cabinets.

Limitations
The Base plate is designed to support a maximum of 3 x Y-TOP
cabinets when used directly on the ground.

A maximum of 6 x Y-TOP cabinets are allowed when using the
Base plate on top of an applicable d and b subwoofer, such as the
Y-SUB.

The d&b MAX 15 Stage Monitor is a high‑performance 2‑way full‑range wedge format loudspeaker.

The MAX uses a 15‑inch LF driver paired with a coaxially mounted 2‑inch compression driver. This design delivers a coherent sound field with strong vocal projection and excellent feedback stability. Its 60° conical dispersion provides a clearly defined coverage area on stage. The MAX can also operate in both passive and active modes. Users can position the MAX 15 as a low‑profile floor wedge or use it upright as a compact PA loudspeaker.

The MAX cabinet is constructed from marine plywood with integrated handles. It features an impact‑resistant paint finish, M10 threaded inserts, a stand socket, and ratchet‑strap guide plates for secure deployment. A rigid metal grille backed with acoustically transparent foam protects the front of the cabinet.

The MAX delivers a frequency response from 55 Hz to 18 kHz and achieves up to 136 dB SPL depending on amplifier mode. The MAX 15 is no longer a current d&b product, but you can still find the full specifications in the heritage section of their website.

IPS hire stock d&b MAX 15 Stage Monitor include NL4 connectors and come supplied in two‑way flightcases. You can drive the MAX 15 with a range of d&b amplifiers, including the D6, D12 and D80. IPS has a range of d&b loudspeakers, amplifiers and processing equipment ready to hire, including an extensive range of other audio hardware.

The d&b M4 Stage Monitor is a high‑performance 2‑way loudspeaker. Almost universally accepted on any performer or artist rider, you’ll find the M4 on a huge number of stages – and the techs love them too.

The M4 uses an integrated 15‑inch 1D LF driver and a 1.3‑inch 1D exit horn‑loaded HF coaxial driver, both featuring neodymium magnets. Its constant‑directivity horn provides a 50° x 70° (h x v) dispersion pattern, delivering a precisely defined coverage area on stage. You can also operate the M4 in 2‑Way Active mode.

You can position the cabinet upright, allowing the M4 to function as a powerful PA loudspeaker. In this orientation, it provides a 70° x 50° dispersion suitable for a wide range of applications. For installation use, you can rotate the M4’s driver assembly in 45° increments to achieve the desired dispersion characteristics.

The M4 cabinet is built from marine plywood with integrated handles. It features an impact‑resistant paint finish, M10 threaded inserts, and a socket for loudspeaker stands. A rigid metal grille backed with acoustically transparent foam protects the front of the cabinet. Two recessed runners on the bottom panel protect the enclosure from scratches and prevent movement. Full M4 specifications are available on the d&b audiotechnik website.

IPS hire stock d&b M4 Stage Monitors include NL4 connectors and come supplied in two‑way flightcases. You can drive the M4 with a range of d&b amplifiers, including the D20, D25, D40, and D80. IPS has a range of d&b loudspeakers, amplifiers and processing equipment ready to hire, including an extensive range of other audio hardware.

The d and b M20 heavy-duty steel tubing speaker stands with variable height-adjustment by hand crank. Extra safety is provided by a locking screw and bolt. D and B M20 windup speaker stands are for use with d and b Subs and Speakers

The Rota clamp must only be used to suspend d and b loudspeaker
cabinets from a single suspension point in connection with
applicable d and b rigging accessories. The Rota clamp allows the
load to be attached to overhead bars or truss with a tube diameter
of up to 50 mm (2inch).

HD 12-A mk5 active speaker boosts performance with a high-power professional 12″ woofer and a 1.4″ HF driver, a 1400W 2ch Class-D amplifier, and innovative FiRPHASE and Bass Motion Control processing. Vocals are natural, the sound is clear at long distances, SPL power is stable at very high levels. The strength of HD series speakers comes from decades of experience building gear for the touring industry, equipping this compact cabinet with power and reliability expected for life on the road. Elegantly designed, the lightweight polypropylene cabinet with internal reinforcement offers maximum strength. The speaker also includes a steel pole mount, threaded inserts for rigging, and rubber handgrips. D-LINE offers working DJs and musicians professional sound designed with music in mind.

The V Series powered loudspeakers delivers absolute value in terms of performance, engineering and design. These ultra-portable speakers combine, in carefully engineered and light-weight cabinets, the clearest and most accurate PROEL sound with Class D amplifier technology and Switch Mode Power Supply, offering an unbeatable PA solution at its price point. All the three models feature an extremely efficient amplifier module capable of delivering 600 W of robust power to the transducers. Thanks to the use of SMPS technology, this power comes in an ultra-lightweight package, making the V models the most portable PROEL speakers ever. The power module is hosted in a fully sealed aluminum box, which provides protection, perfect insulation of the cabinet from the outside and extremely efficient cooling. Thanks to the carefully selected speakers and to the sophisticated active electronics, including dual CLIP LIMITERS for an undistorted sound even at the loudest level, the sound of the V Series has been precisely tuned in every details, in order to provide unheard performance in this price range. The V series cabinets, expression of the most advanced Italian design, include a super-comfortable luggage-style top handle for an effortless portability. The slanted shape allows the V speakers to be laid on their side and used also as stage monitors.

Yamaha MS101 Powered Speaker

Full-range high efficiency loudspeaker.
?9F Wired microphone only.
?9F Can be easily carried via the built-in handle, shoulder
strap, or mounted on a microphone stand.
?9F Each audio source has an individual volume control.

A decorative space saving speaker stand. The heavy cast iron plate with a relatively small diameter requires little space. The
tried-and-tested spring-loaded bolt with locking screw makes height adjustment easy and safe. The stand has a maximum pull-out
height of 1800 mm and is suitable for speakers with a maximum weight of 30 kg. The integrated mounting aid simplifies mounting the
loud speaker cabinets.

Suitable for all K and M speaker stands, tube-diameter 35 mm. With threaded bolt M8 x 18 mm and a large, comfortable handknob

Connecting rod for satellite systems. With spring-loaded
locking screw and safety bolt. Steel tubing.

Two easy-to-carry speaker stands made of high quality aluminum in a carrying case. Fiberglass-reinforced fittings and an additional safety pin ensure stable support for the speakers. The height and feet adjust by an easy-to-use clamping lever.

Worldwide accepted: the speaker stand 214/6 12 robust and sturdy. All clamps are high quality zinc die-cast. The leg construction and large fixed foot end caps enhance safety and stability. Other features are the pull-out guard for the extension tube, the integral anti-shock component and comfortable height adjustment with spring-loaded bolt and locking screw. Comes with a mounting aid on the extension rod.

Steel tube combination for 2 speakers, for tube diameter of 35 mm.

Introducing the d&b audiotechnik U3 Loudspeaker. The U3 is a high-performance, 2-way loudspeaker providing exceptional directivity control and electroacoustic efficiency.

d&b U3 Loudspeaker NLT4 F/M

The point‑source U3 suits both mobile and installation applications, and it represents the next generation of d&b technology and innovation. It features dual 5″ drivers in a bipole arrangement along with a 0.75″ compression driver mounted on a 100° x 65° horn. In addition, you can rotate the horn 90 degrees without using any extra tools (patent pending).

The U3 also leverages new industrial design and manufacturing techniques to achieve state‑of‑the‑art horn geometry and advanced bass‑reflex ports. As a result, it delivers full bandwidth and extended LF output (-5 dB @ 55 Hz with CPL). Furthermore, the U3 provides 65‑degree vertical directivity control starting at 500 Hz, paired with 100‑degree horizontal dispersion.

The cabinet uses highly durable, partially recycled ABS and achieves an IP54 rating for dust and weather resistance. Meanwhile, a rigid metal grille and acoustically transparent foam protect the front. You can stand‑mount or fly the U3. Additionally, a handle and M8 threaded inserts on the back make it easy to attach d&b rigging hardware designed for both mobile and installation use.

Amplifiers & comparisons for the U3

The U3 can be driven by any current d&b amplifier. This includes the D25, D40, D80 and D90, plus all the installation range versions too. You can drive up to three U3 loudspeakers per amplifier channel.

The U3 is the smallest loudspeaker model in the U-Series range. The cabinet dimensions are 411 x 187 x 245 mm with a weight of 7.1kg. This makes the U3 a little larger than the E6 – more similar in dimension to the E8. The audio coverage of the U3 sits just between the E6 and E8, being a little wider than the E6 (and not as quite directional as the E8). All feature a rotatable horn for horizontal or vertical applications.

IPS also stock the larger U5 and U7 loudspeaker cabinets, which are all ready to hire now. You can find out more about the full U-Series on the d&b website here.

IPS hire stock d&b U3 Loudspeaker cabinets are fitted with NLT4 connectors. This means they have an in and an out. They are supplied in four way flight cases, and come complete with stand adaptor and flown rigging options.

Introducing the d&b audiotechnik U5 Loudspeaker. The U5 is a high-performance, 2-way loudspeaker providing exceptional directivity control and electroacoustic efficiency.

d&b U5 Loudspeaker NLT4 F/M

The point‑source U5 suits both mobile and installation applications, and it represents the next generation of d&b technology and innovation. It features dual 6.5″ drivers in a bipole arrangement along with a 1″ compression driver mounted on a 90° x 60° horn. In addition, you can rotate the horn 90 degrees without using any extra tools (patent pending).

The U-series leverages new industrial design and manufacturing techniques to achieve state‑of‑the‑art horn geometry and advanced bass‑reflex ports. As a result, it delivers full bandwidth and extended LF output (-5 dB @ 55 Hz with CPL). Furthermore, the U5 provides 60 degree vertical directivity control starting at 500 Hz, paired with 90 degree horizontal dispersion.

The cabinet uses highly durable, partially recycled ABS and achieves an IP54 rating for dust and weather resistance. Meanwhile, a rigid metal grille and acoustically transparent foam protect the front. You can stand‑mount or fly the U5. Additionally, a handle and M10 threaded inserts on the back make it easy to attach d&b rigging hardware designed for both mobile and installation use.

Amplifiers & comparisons for the U5

The U5 can be driven by any current d&b amplifier. This includes the D25, D40, D80 and D90, plus all the installation range versions too. You can drive up to two U5 loudspeakers per amplifier channel.

The U5 is the middle loudspeaker model in the U-Series range. The cabinet dimensions are 509 x 223 x 295 mm with a weight of 11.5kg. This makes the U5 a little larger than the E8 – more similar in dimension to the E12. The audio coverage of the U5 is almost the same as the E8. All the U-Series loudspeakers feature a rotatable horn for horizontal or vertical applications.

IPS also stock the smaller U3 and larger U7 loudspeaker cabinets, which are all ready to hire now. You can find out more about the full U-Series on the d&b website here.

IPS hire stock d&b U5 Loudspeaker cabinets are fitted with NLT4 connectors. This means they have an in and an out. They are supplied in four way flight cases, and come complete with stand adaptor and flown rigging options.

Introducing the d&b audiotechnik U7 Loudspeaker. The U7 is a high-performance, 2-way loudspeaker providing exceptional directivity control and electroacoustic efficiency.

d&b U7 Loudspeaker NLT4 F/M

The point‑source U7 suits both mobile and installation applications, and it represents the next generation of d&b technology and innovation. It features dual 8″ drivers in a bipole arrangement along with a 1.26″ compression driver mounted on a 80° x 55° horn. In addition, you can rotate the horn 90 degrees without using any extra tools (patent pending).

The U7 also leverages new industrial design and manufacturing techniques to achieve state‑of‑the‑art horn geometry and advanced bass‑reflex ports. As a result, it delivers full bandwidth and extended LF output (-5 dB @ 55 Hz with CPL). Furthermore, the U7 provides 55 degree vertical directivity control starting at 500 Hz, paired with 80 degree horizontal dispersion.

The cabinet uses highly durable, partially recycled ABS and achieves an IP54 rating for dust and weather resistance. Meanwhile, a rigid metal grille and acoustically transparent foam protect the front. You can stand‑mount or fly the U7. Additionally, a handle and M10 threaded inserts on the back make it easy to attach d&b rigging hardware designed for both mobile and installation use.

Amplifiers & comparisons for the U7

The U7 can be driven by any current d&b amplifier. This includes the D25, D40, D80 and D90, plus all the installation range versions too. You can drive up to two U7 loudspeakers per amplifier channel.

The U7 is the largest loudspeaker model in the U-Series range. The cabinet dimensions are 611 x 268 x 355 mm with a weight of 19.2kg. This makes the U7 a little larger than the E12 with a comparable audio coverage and frequency response – albeit with a higher power handling. It could also be seen to sit between the Y7P and Y10P in terms of coverage (and comparable weight/dimension) at a lower rental price point.

IPS also stock the smaller U3 and U5 loudspeaker cabinets, which are all ready to hire now. You can find out more about the full U-Series on the d&b website here.

IPS hire stock d&b U7 Loudspeaker cabinets are fitted with NLT4 connectors. This means they have an in and an out. They are supplied in two way flight cases, and come complete with stand adaptor and flown rigging options.